borescoring.com
Which Porsche engines, how to check, what to ask.

Porsche bore scoring, explained and checked.

Porsche bore scoring is wear damage to the cylinder wall and piston skirt that raises oil consumption. Pick a Porsche engine to see whether independent sources describe it for that engine.[1][3]

Four possible answers: documented, reported, not documented, single source. The answer describes an engine type, not one car.

Bore scoring by engine

Bore scoring is documented on the M96 and M97 engines of the 996, 997.1 and 987.1 with Lokasil cylinders; the 2.5 to 3.2-litre Boxster and Cayman engines and the Mezger engines are not documented.[1][2][3]

EngineBore surfaceLabel
M96 3.4 (996.1)LokasilDocumented less often
M96.03 3.6 (996.2)LokasilDocumented
M96.05 3.6 (996.2 / 997.1)LokasilDocumented
M97.01 3.8 (997.1 S)LokasilDocumented
M97.21 / .22 3.4 (987.1 S)LokasilDocumented
2.5 / 2.7 / 3.2 (986, 987.1)LokasilNot documented
MA1 / 9A1 (987.2, 997.2, 981, 991.1)AlusilReported lower rate
Mezger 3.6 / 3.8 (Turbo, GT2, GT3)NikasilNot documented
V8 4.5 / 4.8 (Cayenne, Panamera)AlusilDocumented
V6 (Macan)AlusilDocumented
Score marks Piston Cylinder wall
Cylinder in cross-section. Scoring shows as vertical marks on the wall. Schematic, not to scale.
01

What it is

Bore scoring is wear damage to the cylinder wall and the piston skirt.[1] Both engine builders describe the same starting point: the coating on the piston skirt fails, and aluminium then runs on aluminium.[1][3]

It usually starts on one bank. Two builders name bank 2, one of them cylinders 4 to 6 with cylinder 6 often first; on the 911, bank 2 is on the right. A press test names the right-hand bank with a sooty left tailpipe.[3][8][5]

No fleet-wide failure rate is published. A 2015 magazine article quotes three UK workshops: about 1 % of 1,500 cars inspected at one, about 2.5 % of the 3.6 and 3.8 engines seen at another, and 0.2 % at a third. The samples differ and are not a rate for all cars.[7]

02

How to recognise it

Three signs are named by two sources each: rising oil consumption, a ticking or tapping noise from piston slap that is often taken for lifter noise, and one tailpipe sootier than the other.[1][2][5]

None of these proves scoring on its own.[2]

03

How it is checked

A borescope look at the cylinder walls is the most direct confirmation.[1][2] Oil analysis alone does not confirm scoring.[1][2]

Two sources add that compression and leak-down tests can stay normal in early scoring.[1][19]

04

What it costs to fix

Two sources say oil, additives or a flush do not reverse scoring; the lasting fix means taking the engine apart.[1][20] One builder says early cases can sometimes be saved without a full rebuild.[18] Both builders name the same lasting repair: the bore surface is replaced with Nikasil-plated aluminium cylinders.[1][3]

Sources disagree on boring to oversize with matching pistons. Hartech reported that it did not last, but its later interim engine guide calls its most recent versions reliable; Cartronic expects repeat damage on re-bored cylinders.[3][25][24]

Cost figures

Six figures from three markets. They are shown separately with source and date, not as one merged range.

US$5,000–6,000Cylinder repair of the block only. LN Engineering, undated.[4]Single source
US$15,000–30,000 or moreFull rebuild including the cylinder repair. LN Engineering, undated.[4]Single source
from €25,000Engine overhaul, Germany. Auto Bild, 22 September 2026.[5]Single source
€9,500 plus VATEngine overhaul (3.4/3.6/3.8) with new grey-iron cylinder liners, Germany; removal and refit €2,200 plus VAT extra. A&G Sportwagen Service, offer of 28 October 2026.[21]Single source
US$15,000–25,000M96/M97 rebuild, Connecticut. Repasi Motorwerks, undated, retrieved 21 November 2026.[22]Single source
£13,000–15,000996 or 997 rebuild with bore-scoring repair, UK. Tech 9 Motorsport, undated, retrieved 21 November 2026.[23]Single source

Causes: two explanations

Common ground. The coating on the piston skirt fails, and aluminium then runs on aluminium.[1][3] Two sources agree

Explanation A · LN Engineering

A breakdown of the whole aluminium-silicon cylinder system. Contributing factors are a thin oil film, fuel wash, injector or mixture faults, local temperature and long cold running. Longer stroke adds side load on the 3.6 and 3.8.[1][2]

Explanation B · Hartech

Loose silicon particles from the Lokasil bore wear through the softer piston coating used on later engines. Bank 2 runs hotter and goes first. Fuel, injectors and oil type would hit both banks equally, so they are not the main cause.[3]

Cite this

Bore scoring is documented on the M96 and M97 engines of the 996, 997.1 and 987.1 with Lokasil cylinders; the 2.5 to 3.2-litre Boxster and Cayman engines and the Mezger engines are not documented. Source: Porsche Bore Scoring: Affected Engines, Symptoms, Cost, https://borescoring.com/ (checked 2026-11-20).
Data licensed CC BY 4.0: reuse with attribution to borescoring.com.

Sources and method

Each engine gets one label. Documented means two independent sources describe scoring on this engine. Reported means one technical source or owner reports only. Not documented means the sources name the engine as not typically affected. Single source means one source only.

The three LN Engineering pages count as one source. A label describes an engine type and says nothing about one car.

  1. [1]LN Engineering: Porsche Cylinder Bore Scoring
  2. [2]LN Engineering: What Is Porsche Cylinder Bore Scoring
  3. [3]Hartech, Barry Hart: bore scoring report, as posted on Rennlist
  4. [4]LN Engineering: Bore Scoring Repair Costs
  5. [5]Auto Bild: Porsche 911, five generations in the used-car check, 22 September 2026
  6. [6]Rennlist: bore scoring owner survey, Cayenne 955 and 957
  7. [7]GT Porsche (Peter Morgan): M96/97 engines, cylinder bore scoring, March 2015
  8. [8]Backshop Technik: Porsche bore scoring, how it is checked
  9. [9]Backshop Technik: ticking Macan engine
  10. [10]FCP Euro: first-generation Cayenne engine options (955/957)
  11. [11]Only VAG: relining the Cayenne 4.8 after scoring (ru)
  12. [12]PistonHeads: Panamera (970) used buying guide, 3 April 2017
  13. [14]KickTyres: Boxster/Cayman common faults
  14. [15]Porsche Inspections: FAQ
  15. [16]Motorschmiede: Porsche 997 engine problems (de)
  16. [17]Total 911, issue 243 (2024): M96 & M97, five failures and fixes
  17. [18]Flat Six Innovations: cylinder bore scoring, 25 November 2025
  18. [19]A&B Import Auto: Porsche bore scoring diagnosis
  19. [20]ASF Machine: Porsche bore scoring repair
  20. [21]A&G Sportwagen Service: engine overhaul offer, 28 October 2026 (de)
  21. [22]Repasi Motorwerks: Porsche engine rebuild
  22. [23]Tech 9 Motorsport: Porsche engine rebuilding
  23. [24]Cartronic Motorsport: TimeOver, version of 10 August 2018 (de)
  24. [25]Hartech: engine guide (interim)

Last updated 2026-11-20

The full data set lives on typenwerk.ai

Every engine with its known fault patterns and the sources behind each entry.

Questions

Does “Documented” mean my engine is affected?

No. Documented means two independent sources describe scoring on this engine type. For one car, a borescope look at the cylinder walls is the most direct confirmation.[1][2]

Does “Not documented” mean the engine is safe?

No. It means the sources name this engine as not typically affected. That is not proof of absence for one car.

How common is bore scoring?

No fleet-wide failure rate is published. A 2015 magazine article quotes three UK workshops: about 1 % of 1,500 cars inspected at one, about 2.5 % of the 3.6 and 3.8 engines seen at another, and 0.2 % at a third. The samples differ and are not a rate for all cars.[7]

Can oil or additives reverse it?

No. Two sources say oil, additives or a flush do not reverse scoring; the lasting fix means taking the engine apart. One builder says early cases can sometimes be saved without a full rebuild.[1][20][18]

Can it be prevented?

No practice guarantees prevention.[1] The two engine builders give different advice and each point has one source, so this page links to both instead of repeating it.[1][3]

Why are there two explanations for the cause?

Both builders say the piston-skirt coating fails and aluminium runs on aluminium. LN Engineering describes a breakdown of the whole cylinder system; Hartech points to loose silicon particles from the Lokasil bore.[1][2][3]